Every temperature record in your diary depends on one small piece of equipment telling the truth. A probe that reads two degrees high will pass a chicken that is not cooked, and nobody will know until someone is ill. The "Prove it" sheet in the SFBB pack for caterers says to check the probe regularly, for example once a month, for exactly this reason. It is one of the cheapest pieces of food safety you will ever do. Two glasses, two minutes.
The two tests
View as a table
| Test | Expected | Pass range | If it fails |
|---|---|---|---|
| Iced water | 0°C | -1°C to +1°C | Replace or send for calibration |
| Boiling water | 100°C | 99°C to 101°C | Replace or send for calibration |
Iced water
- 1Fill a glass with crushed iceThen add just enough cold water to fill the gaps. It should be slush, mostly ice.
- 2Stir and waitAbout a minute, so the water reaches 0°C throughout.
- 3Insert the probeInto the middle of the slush, not touching the glass. Wait for the reading to settle.
- 4Read and recordBetween -1°C and +1°C is a pass. Write the date, reading and result.
Boiling water
Bring a pan to a rolling boil, put the probe tip in the water without touching the pan, wait for the display to settle, and read it. 99°C to 101°C is a pass. Water boils at a slightly lower temperature at altitude, but nowhere in the UK is high enough for that to matter. Be careful with the steam.
You only need one of the tests to check the probe, and ice water is the safer one. Doing both tells you the probe is accurate across the range, which matters because a probe can be right at 0°C and wrong at 75°C.
Probe or infrared?
| Digital probe | Infrared | |
|---|---|---|
| Core temperature of cooked food | Yes | No |
| Reheating and hot holding | Yes | No |
| Quick fridge surface spot checks | Partly | Yes |
| Reflective packaging | Yes | No |
| Needs cleaning between uses | Yes | No |
| Can be left in the oven | No | No |
Probe care
A good probe gives bad readings when it is mistreated. The pack's care rules are short:
- Clean and disinfect before and after every useProbe wipes, kept moist. A dirty probe is a cross-contamination route from raw to cooked.
- Wait for the display to stop movingReading too early gives a low number.
- Keep it away from heat and liquidsDo not leave it in the fridge, on the pass or in a pan.
- Do not drop itA drop can knock the sensor out of calibration. Recheck after any knock.
- Replace a low battery straight awayLow batteries cause drifting readings before the display dies.
- Have a spareA kitchen with one probe and no spare has no probe the day it fails.
The probe check is opening check 8 in the daily diary ("probe thermometer is working and probe wipes are available"), so the daily version is a glance and the monthly version is the test above. Both are covered in the SFBB daily diary explained. For what you are probing for once you trust the number, see 70°C for 2 minutes explained.
Questions people ask
How often should a food probe be calibrated?
The SFBB pack says to check it regularly, for example once a month, and it is one of the questions in the 4-weekly review. Many kitchens do it weekly because it takes two minutes. Also do it after the probe is dropped, after a battery change, and whenever a reading looks wrong.
Can I calibrate a probe myself?
You can check it yourself with the ice water and boiling water tests. Most kitchen probes cannot be adjusted, so if it fails the check, replace it or send it to the manufacturer for calibration. A certificate from an accredited calibration is only needed if your own system or a customer requires it.
Can I use an infrared thermometer instead of a probe?
For surface spot checks in a fridge, yes. For cooking, reheating and hot holding, no. Infrared reads the surface, and the surface of a chicken thigh is not where the bacteria survive. You need a probe in the centre.
My probe reads 2°C in ice water. Is that a fail?
Yes. The pass range is -1°C to +1°C. A probe that is 2°C out will tell you a 68°C chicken is 70°C. Replace it.